View PAM2303CFGADJR_8283244.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

pam2303 document number: dsxxxxx rev. 1 - 2 1 of 14 www.diodes.com november 2012 ? diodes incorporated pam2303 a product line o f diodes incorporated 3a low noise step-do wn dc-dc converter description the pam2303 is a 3a step-down dc-dc converter. it operates in two different modes: psm and pwm modes. at light load, it automactically enters into the psm mode to improve efficiency. at heavy load, the constant frequency pwm control performs excellent stability and transient response. no external compensation components are required. the pam2303 supports a range of input voltages from 2.7v to 5.5v. the output voltage is adjustable from 0.6v to the input voltage. the pam2303 employs internal power switch and synchronous rectifier to minimize external part count and realize high efficiency. during shutdown, the input is disconnected from the output and the shutdown current is less than 1a. other key features include over- temperature and short circuit prot ection, and under-voltage lockout to prevent deep battery discharge. the pam2303 delivers 3a maximum output current while consuming only 42a of no-load quiescent current. ultra-low r ds(on) integrated mosfets and 100% duty cycle operation make the pam2303 an ideal choice for high-output volta ge, high-current applications which require a low dropout threshold. the pam2303 is available in sop-8(ep), dfn3x3-10 and qfn3x3- 16 package. features ? output current: up to 3a ? output voltage: 0.6v to v in ? input voltage: 2.7 to 5.5v ? efficiency up to 95% ? 42a (typ) no load quiescent current ? shutdown current: <1a ? 100% duty cycle operation ? 1.5mhz switching frequency ? analog soft start ? no external compensation required ? current limit protection ? thermal shutdown ? sop-8(ep), dfn3x3-10 and qfn3x3-16 package pin assignments applications ? 5v or 3.3v point of load conversion ? telecom/networking equipment ? set top boxes ? storage equipment ? video cards ? ddr power supply
pam2303 document number: dsxxxxx rev. 1 - 2 2 of 14 www.diodes.com november 2012 ? diodes incorporated pam2303 a product line o f diodes incorporated typical applications circuit ? ? ? ? ? ? + = 2 r 1 r 1 6 . 0 v o pin descriptions pin name package name function qfn3x3-16 sop-8ep dfn3x3-10 pgnd 1, 2, 3 2 ? main power ground pin. fb 4 3 6 feedback voltage to internal error amplifier, the threshold voltage is 0.6v. gnd 5 4 4 signal ground for small signal components. nc 6, 16 ? 7 not connected. en 7 5 5 enable control input. force this pin vo ltage above 1.5v, enables the chip, and below 0.3v shuts down the device. test 8 6 ? test mode. ?low?connection is recommended. vin 9 7 8, 9, 10 bias supply. chip main power supply pin. pvin 10, 11, 12 8 ? input supply for power stage. must be closely decoupled to pgnd. sw 13, 14, 15 1 1, 2, 3 the drains of t he internalmain and synchronous power mosfet. functional block diagram
pam2303 document number: dsxxxxx rev. 1 - 2 3 of 14 www.diodes.com november 2012 ? diodes incorporated pam2303 a product line o f diodes incorporated absolute maximum ratings (@t a = +25c, unless otherwise specified.) these are stress ratings only and functional operation is not im plied. exposure to absolute maximum ratings for prolonged time periods may affect device reliability. all voltages are with respect to ground. parameter rating unit input voltage pv in , v in 6 v sw pin voltage -0.3 to (pv in +0.3) v fb pin voltage -0.3 to (v in +0.3) v en pin voltage -0.3 to +6.0 v maximum junction temperature 150 c storage temperature range -65 to +150 c soldering temperature 300, 5sec c recommended operating conditions (@t a = +25c, unless otherwise specified.) parameter rating unit supply voltage 2.7 to 5.5 v junction temperature range -40 to +125 c ambient temperature range -40 to +85 thermal information parameter symbol package max unit thermal resistance (junction to ambient) ja sop-8ep 90 c/w dfn3x3-10 60 qfn3x3-16 35 thermal resistance (junction to case) jc sop-8ep 11 dfn3x3-10 8.5 qfn3x3-16 11
pam2303 document number: dsxxxxx rev. 1 - 2 4 of 14 www.diodes.com november 2012 ? diodes incorporated pam2303 a product line o f diodes incorporated electrical characteristics (@t a = +25c, v in = 3.6v, v o = 1.8v, c in = 33f, c o = 22f, l = 2.2h unless otherwise specified.) parameter symbol test conditions min typ max units input voltage range v in 2.7 5.5 v output voltage range v o 0.6 v in v uvlo threshold v uvlo v in rising 2.4 2.5 v hysteresis 240 mv v in falling 1.8 v regulated output voltage accuracy v o i o = 0 to 3a -3 +3 % regulated feedback voltage v fb 0.591 0.600 0.609 v fb leakage current i fb v o = 1v -50 +50 na output voltage line regulation lnr v in = 2.5v to 5v 0.2 %/v output voltage load regulation ldr i o = 0a to 3a 0.5 %/a quiescent current i q no load 42 90 a shutdown current i sd v en = 0v 1 a current limit i lim 4 a oscillator frequency f osc 1.2 1.5 1.8 mhz drain-source on-state resistance r ds(on) high side 85 m ? low side 60 high efficiency 95 % psm threshold i th v in = 3.3v, v o = 1.2v, l = 1h 450 ma analog soft start time t s from enable to output regulation 0.5 ms en threshold high v eh 1.5 v en threshold low v el 0.3 v en leakage current i en v in = v en = 0v -1.0 +1.0 a over temperature protection otp 150 c otp hysteresis oth 30 c
pam2303 document number: dsxxxxx rev. 1 - 2 5 of 14 www.diodes.com november 2012 ? diodes incorporated pam2303 a product line o f diodes incorporated typical performance characteristics (@t a = +25c, c in = 10f, c o = 10f, l = 4.7h unless otherwise specified.)
pam2303 document number: dsxxxxx rev. 1 - 2 6 of 14 www.diodes.com november 2012 ? diodes incorporated pam2303 a product line o f diodes incorporated typical performance characteristics (cont.) (@t a = +25c, c in = 10f, c o = 10f, l = 4.7h unless otherwise specified.)
pam2303 document number: dsxxxxx rev. 1 - 2 7 of 14 www.diodes.com november 2012 ? diodes incorporated pam2303 a product line o f diodes incorporated typical performance characteristics (cont.) @t a = +25c, c in = 10f, c o = 10f, l = 4.7h unless otherwise specified.)
pam2303 document number: dsxxxxx rev. 1 - 2 8 of 14 www.diodes.com november 2012 ? diodes incorporated pam2303 a product line o f diodes incorporated application information the basic pam2303 application circui t is shown in page 1. external component sele ction is determined by the load requirement, s electing l first and then c in and c out . inductor selection for most applications, the value of the inductor will fall in the range of 1 h to 3.3 h. its value is chosen based on the desired ripple current and efficiency. large value inductors lower ripple current and small value inductors result in higher ripple currents. higher v in or v out also increases the ripple current as shown in equation 3a reas onable starting point for setting ripple current is i l = 1.2a (40% of 3a). ()( ) ? ? ? ? ? ? ? ? ? = v v 1 v l f 1 i in out out l equation 1 the dc current rating of the inductor should be at least equal to the maximum load current plus half the ripple current to prev ent core saturation. thus, a 4.2a rated inductor should be enough fo r most applications (3a + 1.2a). for be tter efficiency, choose a low dc-resistan ce inductor. v o 1.2v 1.5v 1.8v 2.5v 3.3v l 1h 1.5h 2.2h 2.2h 3.3h c in and c out selection in continuous mode, the source current of the top mosfet is a square wave of duty cycle v out /v in . to prevent large voltage transients, allow esr input capacitor sized for the maximum rms current must be used. the maximum rms capacitor current is given by: () [] v v v v i i required c in 2 / 1 out in out omax rms in ? ? this formula has a maximum at v in = 2v out , where i rms = i out /2. this simple worst-case condition is commonly used fo r design because even significant deviations do not offer much relief. note that the capacitor manufacturer's ripple current ratings are often based on 2000 hours of life. this makes it advisable to further derate the capacitor, or choos e a capacitor rated at a higher temperature than required. con sult the manufacturer if there is any question. the selection of c out is driven by the required effe ctive series resistance (esr). typically, once the esr requirement for c out has been met, the rms current rating generally far exceeds the i ripple (p-p) requirement. the output ripple v out is determined by: v out i l (esr = 1/8fc out ) where f = operating frequency, c = output capacitance and i l = ripple current in the inductor. for a fixed output voltage, the output ripple is highest at maximum input voltage since i l increases with input voltage. using ceramic input and output capacitors higher values, lower cost ceramic capacitor s are now becoming available in smaller ca se sizes. their high ripple current, high voltage rating and low esr make them ideal for switching regulator applications. using ceramic capacitors can achi eve very low output ripple and s mall circuit size. when choosing the input and output ceramic c apacitors, choose the x5r or x7r dielectric formulations. thes e dielectrics have th e best temperature and voltage characteristics of a ll the ceramics for a given value and size. thermal consideration thermal protection limits power dissipation in the pam2303. when t he junction temperature exceeds +150c, the otp (over tempera ture protection) starts the thermal shutdown and turns the pass tr ansistor off. the pass transistor resumes operation after the junc tion temperature drops below +120c. for continuous operation, the junction tem perature should be maintained below +125c. the power dissipation is defined as: ( ) () v i i f t v r v v r v i p in q o s sw in dsonl o in dsonh o 2 o d + + ? + = i q is the step-down converter quiescent current. the term tsw is used to estimate the full load step-down converter switching los ses.
pam2303 document number: dsxxxxx rev. 1 - 2 9 of 14 www.diodes.com november 2012 ? diodes incorporated pam2303 a product line o f diodes incorporated application information (cont.) thermal consideration (cont.) for the condition where the step-down converter is in dropout at 100% duty cycle, the tota l device dissipation reduces to: p d = i o 2 r dson h +i q v in since r ds(on) , quiescent current, and switching losses all vary with input vo ltage, the total losses should be investigated over the complet e input voltage range. the maximum power dissipation depends on the thermal resistance of ic package, pcb layout, the rate of surroundi ng airflow and temperature difference between junction and ambient. the maximu m power dissipation can be calculated by the following formu la: ? = ja a ) max ( j d t t p where tj(max) is the maximum allow able junction temperature +125c. t a is the ambient temperature and ja is the thermal resistance from the junction to the ambient. based on the standard jedec for a two layers thermal test board, the thermal resistance ja of qfn3x3-16 68c/w and sop-8(ep) 90c/w, respectively. the maximum power dissipation at t a = +25c can be calculated by the following formula: p = (125c - 25c)/68c/w = 1.47w(qfn3x3-16) p = (125c - 25c)/90c/w = 1.11w(sop-8) setting the output voltage the internal reference is 0.6v (typical). the output voltage is calculated as below: the output voltage is given by table 1. ? ? ? ? ? ? + = 2 r 1 r 1 6 . 0 v o table 1 : resistor recommended for output voltage setting v o r1 r2 1.2v 150k 150k 1.5v 225k 150k 1.8v 300k 150k 2.5v 475k 150k 3.3v 680k 150k pulse skipping mode (psm) description when load current decreases, the peak switch current in power-pmo s will be lower than skip current threshold and the device wil l enter into pulse skipping mode. in this mode, the device has two states, working state and idle state. first, the device enters in to working state cont rolled by internal error amplifier.when the feedback voltage gets higher than internal refe rence voltage, the device will enter into low i idle state wi th most of internal blocks disabled. the output voltage will be reduced by loading or leakage current. when the feedback voltage gets lower than th e internal reference voltage, the convertor will start a working state again. 100% duty cycle operation as the input voltage approaches the output voltage, the converte r turns the p-channel transistor continuously on. in this mode the output voltage is equal to the input voltage minus the vo ltage drop across the p-channel transistor: v out = v in ? i load (r dson + r l ) where r dson = p-channel switch on resistance, i load = output current, r l = inductor dc resistance uvlo and soft-start the reference and the circuit remain reset until the v in crosses its uvlo threshold. the pam2303 has an internal soft-start circuit that limits the in -rush current during start-up. this prevents possible voltage drops of the input voltage and eliminates the output voltage overshoot. the soft-start make the output voltage rise up smoothly.
pam2303 document number: dsxxxxx rev. 1 - 2 10 of 14 www.diodes.com november 2012 ? diodes incorporated pam2303 a product line o f diodes incorporated application information (cont.) short circuit protection the switch peak current is limited cycle-by-cycle to a typical value of 4a. in the event of an output voltage short circuit, th e device operates with a frequency of 500khz and minimum duty cycle, therefore the average input current is more smaller than current limit. thermal shutdown when the die temperature exceeds +150c, a reset occurs and the reset remains until the temperature decrease to +120c, at whic h time the circuit can be restarted. ordering information part number output voltage package packaging pam2303ajeadjr adj qfn3x3-16 3000 units/tape & reel pam2303becadjr adj sop-8ep 2500 units/tape & reel PAM2303CFGADJR adj dfn3x3-10 3000 units/tape & reel marking information
pam2303 document number: dsxxxxx rev. 1 - 2 11 of 14 www.diodes.com november 2012 ? diodes incorporated pam2303 a product line o f diodes incorporated package outline dimensions (all dimensions in mm.) sop-8ep
pam2303 document number: dsxxxxx rev. 1 - 2 12 of 14 www.diodes.com november 2012 ? diodes incorporated pam2303 a product line o f diodes incorporated package outline dimensions (cont.) (all dimensions in mm.) dfn3x3-10
pam2303 document number: dsxxxxx rev. 1 - 2 13 of 14 www.diodes.com november 2012 ? diodes incorporated pam2303 a product line o f diodes incorporated package outline dimensions (cont.) (all dimensions in mm.) qfn3x3-16 notes: 1. controlling dimensions are millimeters (angles in degrees). 2. coplanarity applies to the exposed pads as well as the terminals. 3. dap is 1.90 x 1.90mm.
pam2303 document number: dsxxxxx rev. 1 - 2 14 of 14 www.diodes.com november 2012 ? diodes incorporated pam2303 a product line o f diodes incorporated important notice diodes incorporated makes no warranty of any kind, express or implied, with regards to this document, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose (and their equivalents under the laws of any jurisdiction). diodes incorporated and its subsidiaries rese rve the right to make modifications, enhanc ements, improvements, corrections or ot her changes without further notice to this document and any product descri bed herein. diodes incorporated does not assume any liability ari sing out of the application or use of this document or an y product described herein; neither does di odes incorporated convey any license under its patent or trademark rights, nor the rights of others. any customer or us er of this document or products described herein in such applica tions shall assume all risks of such use and will agree to hold diodes incorporated a nd all the companies whose products are represented on diodes incorporated website, harmless against all damages. diodes incorporated does not warrant or accept any liability w hatsoever in respect of any products purchased through unauthoriz ed sales channel. should customers purchase or use diodes inco rporated products for any unintended or una uthorized application, customers shall i ndemnify and hold diodes incorporated and its representativ es harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death a ssociated with such unintended or unauthorized application. products described herein may be covered by one or more united states, international or foreign patents pending. product names and markings noted herein may also be covered by one or more united states, international or foreign trademarks. this document is written in english but may be translated into multiple languages for reference. only the english version of t his document is the final and determinative format released by diodes incorporated. life support diodes incorporated products are specifically not authorized for use as critical component s in life support devices or systems without the express written approval of the chief executive offi cer of diodes incorporated. as used herein: a. life support devices or syst ems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when proper ly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. b. a critical component is any component in a life support devic e or system whose failure to perform can be reasonably expect ed to cause the failure of the life support device or to affect its safety or effectiveness. customers represent that they have all necessary expertise in the safety and regulatory ramifi cations of their life support dev ices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-rel ated requirements concerning the ir products and any use of diodes incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or s ystems-related information or support that may be provided by diodes incorporated. further, customers must fully indemnify diodes incorporate d and its representatives against any damages arisi ng out of the use of diodes incorporated pr oducts in such safety-critical, life suppor t devices or systems. copyright ? 2012, diodes incorporated www.diodes.com

▲Up To Search▲

Price & Availability of PAM2303CFGADJR

	To Download PAM2303CFGADJR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .